银离子抗菌整理剂 SilverClear

银离子抗菌整理剂

SilverClear

SilverClear 是以银离子为主要成分的抗菌溶液,目前已被美国环保署(US EPA )认证(注册号;84630-2) ,作用原理为分子释放两种类型的离子,阳性分子可以迅速撕裂细菌的保护壁,较小的银离子随后进入破坏细菌的外膜,扰乱细菌的呼吸系统及破坏细菌的DNA ,经AATCC 100的检测,在经过多达100次洗涤之后,仍具有优异的抗菌、杀菌效果。可广泛应用于棉、涤纶、尼龙、晴纶等织物。

一、物化性能             

外观:乳白色液体

离子型:阳离子

pH: 2.5-4.0

溶解性:易溶于水

兼容性:与树脂,粘合剂,氟碳防水剂及其它整理助剂有很好的相容性。                

二、使用方法

可参照下面顺序试验后使用:

1.浸轧及涂层  采用浸轧工艺使用SilverClear , 轧余率在30% - 60%左右。为了获得更好的抗菌效果,建议SilverClear 在最后-槽中加入(烘干前)。用量2%-5% ,如加大该产品用量,抗菌效能及耐洗涤能力也会显蓍提高

2.喷涂法  SilverClear 可以用稀释液(20%及以上)或原液进行喷涂应用。由于该产品不含任何有害溶剂,所以在准备SiIverClear 工作液或应用时，不需要专门的通风，排气装置。当然 ,必须遵守当地的职业健康要求规定。为了获得更好的抗菌性能, SilverClear 应在最后一步整理中使用。

3.烘干及烘培  为了获得更好的耐洗性能 ,处理后的织物需要在120℃烘干，然后在170℃ -180℃烘培20秒以上

产品性能

1.有效杀灭细菌、真菌、霉菌,从而让纺织品保持清新无异味。

2.不影响产品手感及光泽

3.使用简单，能与其他产品一起应用，无需额外加工工艺

4.适用于纤维、纱线纺织面料、纸张过滤材料、机织物、无纺布。

5.已在美国环保署注册认证

贮    存

1.使用前请搅拌均匀。通过较剧烈的搅拌 或揽拌(涡旋)确保容器底部没有任何沉淀物。可以使用带有 3叶螺旋桨的电动搅拌器以获得良好搅拌效果。尽量避免产生过多泡沫。SilverClear溶液应储存在桶中 ，放置于阴凉干燥的环境里,并避免强紫外线照射。

2.禁止暴晒以及放置在高温环境下。

Silver Ion Antibaterial

Finishing Agent

HOLPOSON® SilverClear

SilverClear is an antibacterial solution with silver ion as the main component. It has been certified by US EPA (Registration Number: 84630-2) at present. The working principle is as follows: Molecules release two types of ions. Positive molecules can tear the protective wall of bacteria rapidly. The smaller silver ions then enter and destroy the outer membrane of bacteria to destroy the respiratory system and DNA of bacteria, After AATCC 100 detection, more than 99.9% of the bacteria can be eliminated quickly. After up to 100 times of washing, it still has excellent anti-bacteria and sterilization effect. It can be widely used in cotton, polyester, nylon, acrylic and other fabrics.

Physical & chemical properties:             

Appearance: Milky white liquid

Ionicity: Cationic

pH: 2.5-4.0

Solubility: Soluble in water

Compatibility: Good compatibility with resins, adhesives, fluorocarbon water proofing agents and other finishing agents.    

Usage:

It can be used after the following sequence of tests:

1. SilverClear is used for padding and coating, with a liquid rate of 30% - 60%. For the better antibacterial effect, SilverClear is recommended to be added in the last bath (before drying). The dosage is 2% - 5%. If the dosage of the product is increased, the antibacterial effect and washing resistance will also be improved.

2. Spray method. SilverClear can be applied as a diluted solution (20% or more) or original solution. Since the product does not contain any harmful solvents, there is no need for special ventilation device when preparing SilverClear working solution or during usage. Of course, local occupational health requirements must be observed. In order to obtain the better antibacterial performance, SilverClear should be used in the final finishing step.

3. Drying and baking in order to obtain the better washing resistance, the treated fabric needs to be dried at 120℃ and then baked at 170℃-180℃ for more than 20 seconds.

Characteristics:

1. Effectively kills bacteria, fungi and molds, so as to keep textiles fresh and odorless.

2. Does not affect the hand feel and luster of the product.

3. It is easy to use and can be used with other products without additional processing technology.

4. Suitable for fiber, yarn knitted/woven fabrics, paper filter materials, woven fabrics, non-woven fabrics.

5.Registered and certified by EPA.

Storage:

1. Stir evenly before use. Make sure that there is no sediment at the bottom of the container by more vigorous stirring or stirring (vortex). An electric stirrer with a 3-Blade propeller can be used for better mixing. Try to avoid creating too many bubbles. SilverClear solution should be stored in a bucket, in a cool and dry environment, and avoid strong ultraviolet radiation.

2. It is forbidden to expose to the sun or place in high temperature.