防水防油整理剂AG-E 082

防水防油整理剂AG-E 082

AG-E 082赋予各种纤维以优异的防水防油特性:稳定性佳，受前道工序的残留物染料及拼用助剂影响小:不属于日本消防法的危险物，使用便利

一、物化性能             

外观         淡黄色乳液

pH值         酸性

比重（20℃）  1.1

含固量     20%

离子性       弱阳离子

溶解性       易稀释分散于水中                 

二、使用方法

AG - E082通常通过浸轧法加工使用。标准处方的使用浓度根据对象纤维材料、纤维以及使用目的而有所不同。一般情况下使用浓度为:

一般防水防油加工：AG- E082 20-60 g/L

耐久防水防油加工:

AG - E082 40-100 g/L，末端基封闭型异氰酸酯类交联剂: 10-15g/L

干燥条件100-120℃ 1-3分钟

烘焙条件: 150-170℃ 1~3分钟

注意事项：

1.含氟加工剂通常具有加深颜色的效果。请提前确认好加工后的成品颜色。

2可以拼用抗静电剂、柔软剂、渗透剂等其他助剂,请事先充分确认其相容性及对防水防油性的影响

3.稀释本品时请用40℃以下的水。加工中请将工作液温度控制在40℃以下.

4.工作液的PH值请调节在7以下弱酸性，在强酸性和碱性的条件下会影响防水防油性能。

5.请尽早使用调配好的工作液.避免加工液的再使甩，

6.请将布料充分洗净。尽量减少残留的亲水物或离子性物质，

7.由于树脂渣易堆积在辊筒上.因此辊简干燥不是理想的方法。

贮    存

1.在搬运本品时,请穿戴合适的个人防护装备，不要将本品直接接触身体。

2.不得吸入本品的蒸汽或雾气。请避免气化或雾化。

3.本产品请在5℃-35℃的范围内贮存,避免阳光直射，密闭保存。在冷冻和长期高温下保存，可能对品质产生不好的影响。

4.将本产品从容器中取出时，请先搅拌均匀。

5.本资料记载的内容仅提供对用户有用的信息,并不作任何保证。

Waterproof and Oil-proof

Finishing Agent

HOLPOSON® AG-E 082

AG-E 082 endows fibers with excellent water-proof and oil-proof properties.It has good stability and receives little influence from residual dyes and jointly-used auxiliaries in the previous process. It is not a dangerous substance under the Japanese Fire Service Law, and is convenient to use.

Physical & chemical properties:             

Appearance:           Pale yellow emulsion

pH value:               Acidic

Specific gravity (20 ℃): 1.1

Solid content:          20%

Ionicity:                Weak cationic

Solubility:              Easily dilutable and dispersable in water

Usage:

AG - E082 is usually used in padding treatment. The concentration in use as per the standard prescription varies according to the target fiber material, fiber and purpose of use. Generally, the concentrations used are:

General waterproof and oil proof processing: AG - E082 20-60g/L

Durable waterproof and oil proof processing: AG-E082 40-100g/L

End blocked isocyanate crosslinkers: 10-15g/L

Drying conditions

100-120 ℃ for 1-3 minutes

Baking conditions

150-170 ℃ for 1-3 minutes

Attentions:

1. Processing agents containing fluorine usually have the effect of deepening the color. Please confirm the color of finished products in advance.

2. Antistatic agents, softeners, penetrants and other auxiliaries can be used together. Please fully confirm their compatibilities and their influences on water and oil resistance in advance.

3. Please use water below 40 ℃ when diluting this product. Please control the working fluid’s temperature below 40 ℃ during processing

4. Please adjust the pH value of the working fluid below 7 in weak acidity, which will affect the waterproof and oil proof performance in strongly acidic and alkaline conditions.

5. Please use the prepared working fluid as early as possible to avoid further reusage of the processing fluid.

6. Please wash the fabric thoroughly to minimize residual hydrophilic or ionic substances.

7. Since resin slag is easy to accumulate on the roller, roller drying is not an ideal method.

Storage:

1. When carrying this product, please wear appropriate personal protective equipment and do not contact the body with the product directly.

2. Do not inhale the vapor or mist of this product. Please avoid vaporization or atomization.

3. Please store the product in the range of 5 ℃ - 35 ℃, avoid direct sunlight, and keep it in a closed place. It may have a bad effect on the quality to keep it in freeze or constant high temperature.

4. When taking the product out of the container, please mix it evenly first.

5. The contents recorded in this document only provide useful information for users without any guarantee.